How To Build A Pitcher's Mound

Make each subsequent layer about 3 to 6 inches smaller in diameter. If building a fully clay mound, dump clay and spread to shape.

An Easy to Follow Ebook for building a portable pitching

Building a portable pitching mound (for under $100) it's a curse being an engineer.

How to build a pitcher's mound. Why you should build a portable pitcher’s mound; I choose that height because in little league the mound is 6 above home plate. A portable pitcher’s mound is a piece of equipment which comes in very handy during bad weather when practice needs to be moved to the nearest area with dry ground or indoor.

Find a space large enough for your mound. The flat section with the rubber is. Your logical side won't let you buy anything that you can make.

See more ideas about pitching mound, baseball pitching, baseball drills. This will be filled with mound material and will prevent it from creeping past the edge of the mound circle during construction and compaction. Remember, the mound needs to slope properly.

I also had them cut the 16' 2x10 into a 10 foot and 6 foot section. This will serve as your frame. As you prepare to construct the mound, use the transit and laser or string lines to make sure home plate, the pitcher’s mound and second base are accurately aligned and everything is square.

Challenges of building a portable pitching mound; Once home, take both of your ten foot planks, mark off the two foot level sections (on opposing ends) and. Build your mound and plate right.

Continue laying smaller and smaller diameter circles of mound clay on top of each other until the mound has reached the height marked on your stake in the center of the circle. Build in 2″ lifts, fully compacting with vibratory plate compactor or roller. Why opt for a portable pitching mound;

Since the rubber is 10” higher than the home plate, the plateau should be level with the rubber and span an area of 5’ by 3’. Repeat steps 2 and 3 until the new surface is level with the old surface. When the pitcher's front foot lands on the slope of the mound, the pitcher has more power behind the ball.

Six inches from the front edge of the table is the pitcher’s plate (also called the rubber), which measures six inches deep by 24 inches wide. How to build the pitcher's plateau. The first step you will need to take when looking to build a pitching mound in your backyard is to find a space large enough.

Drive a stake into the ground with a mallet at the center point of the pitcher’s mound. By building a pitching mound in your backyard, you will always be able to take some time out of your busy day to enjoy a catch with your son or daughter. Major league baseball (mlb) regulations call for the distance from the back of the home plate to the front of the pitching rubber to be 60 feet and 6 inches.

For the base, i started with 4 1 x 10 x 10' pine boards. So you now have two pieces of plywood, three ten foot boards and a six footer. To build a standardized mound, the height needs to be 10 inches of which 2 foot is level section and 6 foot is the slope section.

Remove 2 to 4 inches of existing soil from the stress areas.lightly water. I decided to use a piece of 4' x 8' treated plywood as the main part of the mound. From the middle of the mound, the slope is supposed to decrease approximately one inch per one foot in each direction.

Since the pitcher’s mound is exactly that, a mound, it is not perfectly flat. The end with the pitching rubber is the full width of a 2x6 (~5 1/2 ) and it tapers down to 2 at the bottom. But there should not be a pointed peak, instead there should be a level plateau at the top.

Tamp the clay to a firm but level surface. The pitcher’s mound the flat area atop the diamond, called the table, measures 5 feet wide by 34 inches deep. Cut the plywood to the size that fits the length and width of your frame.

With an edger or a spade, follow the outline and remove all inside turf to establish a permanent boundary for the mound. Usually, these areas don’t have a pitcher’s mound so having a portable one could prove to be very useful. The dimensions of the mound are 84 x 42.

Precisions matters, so measure for every step in the mound building process. Build your mound, step by step. No two areas of the diamond receive more abuse and constant wear than the pitcher’s mound and batter’s/catcher’s boxes.

Simple steps of constructing a portable pitching mound. Moisten the mound throughout construction — it’s important that you keep the soil mixture moistened throughout the building of your pitcher’s mound. Walk around the stake in a circle, keeping the string pulled tight, spraying landscaper’s paint to mark the circle as you go to create the outline of.

Typically, we recommend that the pitcher’s front foot lands on the mound. Nail the plywood onto the frame. Dig a trench 2″ deep and one shovel width wide around the inside edge of the mound.

As you get ready to construct the mound, use the transit and laser (or string lines) to ensure home plate, the pitcher's mound, and second base are accurately aligned and that everything is square. The pitcher's mound is not supposed to be built up like a peak, but rather it should slope up to a firm and level plateau. Smooth the mound, rounding it out where needed, and fill any low spots.

BUILD A PORTABLE PITCHING MOUND Summer 2013 Pinterest